Animodule GATE_MOD Eurorack Modular trigger delay

Let’s face it, couldn’t we ALL use a little more length?

This Tiny (yet powerful) Module allows you to manipulate your gate length and delay your event triggers with ease and minimal impact on your HP.

Take an incoming Signal above ~1.1V (OpAmp Comparators on the Inputs make very forgiving Clock Inputs)
and shrink it down to 5MS or lengthen it up to 5 Seconds.
That Gate will appear at the Gate Out. Continue reading

Synthrotek DS-M Drum Synthesizer Module for Eurorack


the Synthrotek DS-M is an awesome new Drum synth Module for Eurorack.
The DS-M is a full featured drum synth that can emulate virtually any drum sound!

The DS-M (Drum Synth Module) is a complex, modifiable, 100% analog drum synth loosely based on the Coron DS-8 and neatly packaged into an 8hp module.

Continue reading

post

Animodule V9a Eurorack CV controlled sequencer and waveshapper

It’s a wonderful bit of kit that takes your waveforms and turns them into sequencing steps and rhythmic patterns!

V9a

Here’s a powerful animal to add to your sequencing arsenal.

Send your CV to the CV In. As the Voltage increases the sequence steps forward. As the voltage decreases the sequence steps back.
Scale and adjust your input voltage to taste with the Onboard Attenuator and Offset.

Control the Output CV with an individual Potentiometer for each step.

When a step changes, a 10MS trigger is sent to it’s corresponding switch. If the latching switch is depressed it allows the trigger to pass to the Trigger Out.

There is a switch per step for slew (portamento/slide).
and a Potentiometer to control the Slew Amount.
There is also an input to allow gated control of when the slew turns on and off which will work in conjunction with the switches.

This module is looking for 0V to +5V. The Offset is 0V to +5V.

To allow for chaining of the V9a and rests, 0V will put you under the sequencer range and +5V will put you over the sequencer range.
When the sequence drops below step 1 or over step 9, 0V will be sent to the CV Out and No Trigger will be sent to the Trig Out.
When step 1 or 9 is activated a trigger will be sent to the Trig buss.

Max Current Draw:
+12V = 40mA
-12V = 11mA

Width: 14HP Depth: 39mm

Visit the Animodule Store HERE!

Synthrotek Sequence 8 Eurorack Sequencer Build and Demo!

Synthrotek Sequence 8 Eurorack modular sequencer!

 

This is a wonderful 8 step analog sequencer complete with 3 different CV pitch outputs, 8 gate outputs, clock in , clock out, random, random rate, momentary stepping and holding.

Just a very very usable sequencer in a nice compact form that is super powerful. they can even be configured to run off of 9v battery power!

for more info head to Synthrotek.com

XXX_OR from Animdoule for Eurorack modular

Here is a new Module from Eurorack Module maker Animodule.
This is the Triple Exclusive Or “XXX_OR”

It is essentially a logic module that takes up to 6 inputs and combine them to shape the Analog outputs (3) and Gate outputs (3) into interesting sounds and CV. each input is Buffered to the next along with a slight overdrive so each output can get you more shaping. There are so many ways to use this I am needing to do a few videos. (Ring Mod, FM sourcing, Distortion just to name a few)

These are available NOW!

2 new DIY eurorack modules the Tabula Rasa wavetable VCO and the Music thing Spring reverb

Here are two DIY or build them yourself modules for Eurorack. first up is the Tabula Rasa an Arduino based wavetable oscillator that lets you create new waveforms, dump them to SD card and use them in your Eurorack modular. Then we have the Spring reverb from Music Thing which is a voltage controlled spring reverb hooked to a real spring tai. it also has the option of being built with a digital brick reverb tank as well.